How to cut curves in vinyl plank flooring?

When you’re looking for a new floor to add to your home, you must find one that fits your room’s overall design and style. For example, if you have a modern kitchen or living space in your house, having a traditional wood floor would look out of place. In this case, vinyl plank floors are an excellent option because they give off the appearance of real wood without actually being made from it! 

However, one problem people run into when using these products is how do I cut curves? The simple answer is with a sharpie marker! Here’s what you need to know about how to cut curves in vinyl plank flooring.

How can I cut curves in vinyl plank flooring?

Curves can be a difficult task when installing vinyl flooring. There are a few different ways to cut the curves, depending on what you have available for tools and equipment. In this blog post, we will discuss the various methods that people use to cut vinyl planks with curves in them!

Handheld vinyl cutter: 

The first method is using a handheld vinyl cutter. These are typically designed to be used with the smaller flooring panels, however, they can also cut larger ones if done carefully and slowly.

If you do have an actual vinyl cutting machine then this is by far the easiest method of achieving curves in your planks without any difficulty at all!

Use a jigsaw: 

The second option would be to use a jigsaw to cut curves in vinyl plank flooring, again being very careful not to go too fast or push down on it too hard when going through the plank that has no support under it yet (the one for which you want curving). Again though this does take practice, so don’t get frustrated if you mess up a few times before getting it right. Just keep trying different speeds and techniques until you find what works for you.

Hacksaw or electric Jigsaw: 

The third method is the one that most people don’t really want to admit they do, but in reality, it is the easiest by far. It’s a lot of hard work and very time-consuming though so if you’re not patient enough just to wait until your flooring arrives (or order extra) then this method will probably be too much for you!

What we are talking about here is simply cutting around each plank as close as possible with either a hacksaw or an electric jigsaw before putting them down on the ground.

Then once all of your planks have been cut out, using some kind of saw that can easily go around corners such as a miter box cut saw or even another circular saw…you can use these tools to trim off any excess wood and to cut curves. 

What Tools i can use to cut vinyl plank flooring?

There are many different types of flooring available that you can choose from. For example, you might consider vinyl plank flooring but are not sure how to cut it. This article will show you the best way to cut vinyl plank flooring and what tools to use for this type of job!

Vinyl floor cutter: 

The first method to cut vinyl plank flooring is to use a vinyl floor cutter. It is the easiest way to cut your vinyl plank flooring, but make sure you buy the right kind of vinyl planer for this job! 

Regular miter saw hand saw: 

A regular miter saw or hand saw is another way that some people cut their floors, but that can be dangerous and time-consuming if not done correctly. Make sure to measure twice before making any cuts with these tools because they may end up being too short, which will require another trip to the store for more materials!

When cutting your vinyl planks using either miter saws or other tools like hand saws, you wear protective equipment such as safety goggles and gloves. Also, be careful where you are standing while doing these types of jobs because there may be shards flying off at different angles that could potentially hit something nearby, including yourself!

Scoring tool: 

The third method to cut vinyl plank flooring is to use a scoring tool. It is the best way to cut your vinyl plank flooring if you want a professional look, but make sure that it is done correctly, or else they will not line up properly, which can leave gaps between them! Additionally, this method takes more time and effort because one wrong move could mean ruining all of your hard work so far.

Utility knife: 

Another method to cut vinyl plank flooring is a utility knife. This method is straightforward and quick, but it may leave jagged edges, which you will have to go back and fix by either sanding the vinyl down or using a utility knife with a new blade to smooth out those pieces. Some people use this tool for cutting across their flooring; however, we recommend only doing so if your planks are not too long.

The last recommended way of cutting vinyl plank flooring is to measure where each cut needs, turn on an electric hand saw equipped with metal blades, and make cuts along the room’s length. We do not advise turning these tools onto anything other than wood because they can easily scratch up floors such as laminate!

How to Make Straight Crosscuts on Vinyl Planks?

If you install vinyl plank flooring in your home, then the chances are good that one of the first steps is making straight crosscuts. If not, it will happen as soon as you need to break up a sheet of plywood for installation. So how does one make straight cuts on vinyl planks? Read this article and find out!

• The first straight crosscut on vinyl planks is with a straight edge and circular saw.
• Place the vinyl plank against the fence of your table saw, right up to but not touching it. Be sure that you have one of the edges along the blade. So when you turn on the tool and push through, there will be no chance of cutting into or damaging any part. 
• After making this first cut with your circular saw, follow up by using either an electric jigsaw or hand-saw such as a coping saw to get between these cuts and make them deeper if necessary for installation purposes.

Doing this may take some practice before perfecting to ensure proper safety procedures are followed each time without fail! However, the final results should look clean with daming and flooring.

How do you install vinyl planks around curves?

I’ve been installing vinyl plank flooring for years, and when it comes to curves, there are a few things you need to know before you start your installation. Here, we’re going to go over the various ways that you can install vinyl planks around curves so that they look great!

Before installing vinyl planks around curves, the first thing you need to think about is how the flooring will meet at that corner. There are a few different options, like using an inside or outside miter (which we’ll go over in more detail later). Still, there are also some other ways that you can work with when it comes to corners, and they’re all designed to make your installation easier while still looking good:

Double Bump: 

The first option I want to talk about is called the “double bump,” which means running two boards side-by-side and then cutting one of them off, so they overlap each other at the edge. This method keeps both pieces connected, so if something were ever wrong with either piece, you could replace one board instead of having to replace an entire row.

Outside miter: 

The next option is called the “outside miter,” which means you cut one side of your board at a 45-degree angle and then do the same on that end’s corresponding piece (instead of making both cuts for each end). This method creates an overlap between two pieces, so it gives you more room to work with when applying wood filler, sanding down any rough spots, or anything else if needed.

Use trim: 

Last but not least, we have what I like to call the simplest solution available: using another type of trim inside the corner itself. There are many different options here depending on how much money you’re willing to spend and just how fancy you want things to look. However, this will cover up any gaps and make the vinyl plank look completely continuous.

To install these, you’ll want to take a trim piece (in this example, we used quarter round) and cut two pieces that fit perfectly together in your corner, one for each end. After both end pieces are done, place them inside the corner with their outer edge flush against the wall itself. After that, apply wood glue or other adhesive depending on what type of material you’re using, let dry completely before doing anything else. Now, add screws into each side, so they never come out over time. If needed, sand down any rough spots after everything dries up to get things looking just right!

Conclusion: 

Cutting vinyl plank flooring can be a daunting task. So we’ve put together some tips and tricks to help you in how to cut curves in vinyl plank flooring so that it will always look professional and precise. Whether you are using an electric saw or hand tools, we hope these hints will make the job easier for you! Please make sure not to use any power tool other than what is specified in our article, though! Good luck with your next project – we know this one is tough but don’t worry, we’ve got your back!!