Best Way to Cut Vinyl Plank Flooring

One can easily install a contemporary vinyl plank floor instead of installing some expensive hardwood floor. Hardwood floors are popular nowadays, but they require frequent maintenance. The vinyl plank flooring provides a stinking look to your space. However, most people face problems in cutting a vinyl plank floor.

Here in this article, you will learn about some of the best ways of cutting vinyl plank floors. Have a look at the guide below.

All about Vinyl Plank Flooring

Vinyl plank flooring is a straightforward material to work with. It is simple to set up and install. There is no need to use any special tools to cut the vinyl plank flooring without any difficulty. All you need is a laminate tile cutter, circular saw, a table saw, a hand saw, jigsaw, a Dremel, miter saw, utility knife, or more.

The Vinyl flooring is highly light in weight. It is in tongue and groove plank design, making the installation simpler and more manageable. The vinyl planks come in different dimensions that look like wood plank flooring and are usually enclosed with a wood prototype to look a lot like a wooden floor.

However, keep in mind that vinyl planks are not sturdy and thicker than wood planks. So it is crucial to make the right cut while using this material not to damage anything and manage things more accurately.

Tools used to Cut Vinyl Plank Flooring

Vinyl plank flooring is commonly known as LVF or LVP. It normally involves a tongue-in-groove installation technique, also known as the click-lock technique. While cutting a vinyl plank flooring, there are a lot of factors that need to be observed.

The cutting tools you plan to use must not leave any jagged edges on the wood. Such tools must not break the tongue-in-groove edging of the wood also. So it is crucial to pick the right kind of tools for cutting purposes.

One of the appealing characteristics of vinyl board flooring is that it is sufficiently simple to install that you do not need an expert vinyl flooring installer to perform the job for you. Introducing the material is effectively a DIY work that you can attempt as an end-of-the-week project.

Cut Vinyl Plank Flooring Using Tile Cutter

A tile shaper or cutter might be an important tool that you have around your shop that you might consider utilizing as an apparatus to cut your vinyl board flooring.

A tile shaper can be utilized, yet it relies upon the type of tile shaper that you have. Assuming that your tile cutter is a ceramic one, then, at that point, you are up the creek without a paddle. A ceramic tile cutter utilizes a diamond edge shaper to attain the ceramic tile alongside your cut line. It scores the surface by not making deeper cuts.

This is sufficient to confer the ceramic tile a rift along which it will split plainly and break off devoid of cracking the remaining tile. The tile cutter does not provide deep cuts, which means it is not a correct choice for vinyl plank flooring and cannot provide the best possible outcome.

Assuming you have a laminate and vinyl tile shaper with an extremely sharp, guillotine-style edge, this sort of tile shaper is unquestionably reasonable to cut vinyl boards. The guillotine activity of this sharp edge will slice entirely through the vinyl board.

Best Way to Cut Vinyl Plank Flooring

One can use a hand saw to cut the vinyl planks easily, however, avoid making use of a rip saw as it is intended to cut the rough wood with ease. Consider using a saw that contains fine teeth and provides no damage to the edge of the vinyl and results in providing clean cuts.

A handsaw such as an even hacksaw or a finish cut saw will entail teeth that make the cutting process more manageable, help you cut through the material without any difficulty, and provide an even edge after each cut.

However, keep in mind that a flush-cut pull saw helps provide a smooth, clean edge on the vinyl after the slice as the saw teeth are intended to create this kind of cut on wood. While utilizing a saw to cut vinyl boards is feasible, it is considerably more labor-intensive than other faster and more straightforward strategies to cut this material.

Involving a handsaw for cutting the vinyl boards will generously expand how much time that the setting up of the flooring will take. Therefore, it isn’t the most productive method for cutting these boards, yet assuming you have no other choice, it will work; the work will take longer.

Conclusion

Vinyl plank flooring is light in weight and easy to set up and install. It is normally used for easy DIY jobs. Anyone can complete the task without using any sort of professional help.

The Viny plank material is not only simple to work with but simple to cut without using any purpose-built types of equipment or tools to cut the planks correctly without any problem. Most people would have no less than one; however, no doubt a few of the apparatuses we have proposed in this article.

If you are thinking about getting vinyl board flooring for your home, you can think no further! It is an extraordinary decision, particularly in a house with children and pets, since the material is sturdy and waterproof. It likewise looks extraordinary, so it will increase the value of your home without costing you a fortune!